banner



How To Repair A Loose Rod Tip

Download Article

Download Article

Modernistic fishing rods don't break easily, but they can be fixed easily with a few elementary tools you lot may have at home. If your rod snapped, you lot can mend information technology together with a fiberglass pole and epoxy to hide the break. When one of the guides breaks, yous tin remove it and wrap a new ane in its identify. You can alter rod tips if they snap or intermission as well. With a little fleck of work, you can fix your rod so information technology'due south equally skillful as new!

  1. i

    Sand or cut the cleaved ends of the rod so they're flush. Use 180- or 220-grit sandpaper to smoothen the ends so they fit together easily if the rod has a clean suspension. If your fishing rod has a jagged edge, and so use a pair of pair of scissors to cut the abrupt edges off of the end of the rod then the pieces are flush. Later on you brand your cut, employ sandpaper to smooth out the edges and roughen up the surface.[i]

    • Jagged edges are weaker and are more than likely to break again than edges that are flush with 1 another.
  2. 2

    Measure out the circumference of the rod. Utilize a flexible record measure and wrap it around the cleaved finish of your fishing rod. So measure out the circumference on the other piece of your angling rod to come across if it'due south skinnier. Write downwards your measurements and then you know what pole size you need for fixing your rod.[2]

    • Y'all can also measure the bore of the rod on both of the broken ends if you lot don't have a flexible measuring tape.

    Advertisement

  3. three

    Cutting a slice of fiberglass pole and then information technology's about 12 in (30 cm) long. Become a fiberglass pole that has a circumference that'due south about 18 14 inch (0.32–0.64 cm) smaller than your fishing rod. Utilize a hacksaw to cutting out a 12 in (xxx cm) department of the pole so it can fit within your fishing rod and support the rod without breaking.[3]

    • You tin can buy fiberglass poles from your local hardware store. It doesn't matter what colour y'all use since it will fit inside of the rod.
    • If your fishing rod isn't hollow, and so using a fiberglass pole won't work. You tin can either effort to tape your rod dorsum together or become a new one.

    Tip: Y'all can also cutting a section off of an old fishing pole that yous don't use anymore if y'all don't accept a fiberglass rod.

  4. 4

    Slide the fiberglass pole into i side of the fishing rod. Agree your rod horizontally and so you tin can position the fiberglass pole in the rod without it sliding likewise far. Push button 1 end of the fiberglass pole into the cease of the rod with the handle. Keep sliding the pole into the fishing rod until there'due south 6 inches (15 cm) sticking out from the end.[4]

    • If the pole doesn't fit snugly inside the fishing rod, then wrap the pole with duct or masking record to make it thicker.
  5. 5

    Apply ii-part epoxy to the exposed side of the fiberglass pole. Open up your 2-office epoxy and pour it into a bowl. Employ a paintbrush to spread a thin layer of the epoxy on the exposed stop of the fiberglass pole. Once the 2-part epoxy is mixed, work quickly and so it doesn't dry or set before you lot put your rod back together.[5]

    • You tin can buy 2-function epoxy from whatever hardware or craft store.
  6. half dozen

    Slide the other function of the rod onto the fiberglass and let information technology dry. Slowly push button the other end of your rod onto the exposed end of the fiberglass pole. Make certain the guides on the pole line up with i another then your line doesn't get tangled when you try using your pole once again. Push the 2 pieces of the rod together so they're affluent. Permit the epoxy fix overnight and so information technology firmly adheres to the rod.[6]

    • The epoxy doesn't prepare right away, so you tin still rotate or move the rod pieces one time you slide them together.
    • If whatsoever epoxy comes out of the joint while you're sliding the pieces together, wet your finger and polish out the epoxy and then it isn't as visible.
    • Wrap a layer of electric tape effectually the seam if you want an additional layer of security.

    Advert

  1. i

    Cut the tape or thread around the broken guide with a razor blade. Employ a straight razor blade or a craft knife to remove any threading that may be surrounding the rod guide. If it'southward difficult to remove using just a blade, then try heating the surface area for 3-4 seconds with a lighter to loosen whatsoever of the adhesives. Peel off the tape and unwind the threading until the old, broken guide comes off of the rod.[7]

    • Rod guides are the circular metal pieces along the length of the rod that help keep your line straight.
    • Exist conscientious non to heat the rod for too long since information technology could crusade damage to it.
    • Don't cutting into the rod with your razor, or else you could damage it and make information technology weaker.
  2. 2

    Sand the rod and human foot of the new guide to get better adhesion. Use 120- or 220-grit sandpaper to go rid of any leftover agglutinative and to add together molar to the rod. Rub all the way around the rod on the spot where y'all want to identify the new guide. Then, use your sandpaper on the foot of the guide, which is the flat part that rests confronting the fishing rod.[8]

    • You can buy new fishing guides at sporting proficient stores. Brand sure the new guide is the same size and style equally the other guides on your line-fishing rod or else your line may snag or get tangled.
  3. 3

    Tape the new guide onto the rod so it's aligned. Printing the pes of the new guide onto the rod and then it's in line with the other guides. Rip off a thin piece of masking tape and wrap information technology around the foot so it's held in identify. That mode, you don't need to keep belongings it in place while y'all wrap it.[9]

    • Yous can as well use super mucilage, but it will exist hard to move or readjust once the mucilage is set.
  4. four

    Wrap the foot of the guide with thread to agree it in identify. Any type of thread will work for wrapping your guide onto the rod. Loop your threading around the rod so information technology's 1two 34 inch (1.iii–1.9 cm) from the guide'south pes on the side closest to the handle. Maintain tension on the loop and outset tightly winding the thread around the rod. Brand sure the thread doesn't overlap with loops y'all've already made and that they are flush with one another.[10]

    • Take the piece of tape off of the foot you lot've wrapped everything below information technology.

    Tip: Use a thread that matches the color of your rod if you desire information technology to alloy in.

  5. 5

    Place a looped slice of thread over the wrap when there'south ieight  in (0.32 cm) left. When your wrapping is 18 inch (0.32 cm) from the circular part of the guide, finish winding the thread around the pole. Cutting a separate piece of thread so it's most 6 inches (fifteen cm) long and fold information technology in half to form a loop. Lay the 2nd piece of thread on peak of your wrapping so the loop sticks out most your guide.[11]

    • If you don't have any other thread, y'all can also utilise a thin line-fishing line instead.
  6. six

    Wrap the last 18  in (0.32 cm) over the second piece of thread. Once the looped piece of thread is on top of the wrapping, continue spinning your thread around the pes of the guide. Proceed wrapping the last 1eight inch (0.32 cm) of the guide so the middle of the looped piece is held confronting the rod.[12]

  7. 7

    Feed the thread through the looped piece and pull information technology tight. Once you reach the end of your wrapping, cut the end of the thread you used to wrap and pull information technology through the middle of the loop. Pull the other end of the looped slice downwardly and abroad from the guide to pull the thread underneath the wrapping. This mode, the wrapping is secured to the rod without having to tie a knot.[xiii]

    • If you don't want to use a looped piece of thread, you tin can as well try tying a knot in the threading, but it may not exist as strong and information technology could be more than difficult.
  8. eight

    Paint ii-part epoxy onto the thread and let it dry. Mix the 2 parts of the epoxy in a small dish with a paintbrush until they are thoroughly combined. Paint a sparse layer of the epoxy over your threading so it hardens and stays in place. Keep the rod horizontal and permit it dry out overnight before you endeavor using your rod again.[xiv]

    • Work chop-chop with the epoxy since it will quickly get-go to dry out and harden once y'all mix it.

    Advertizement

  1. ane

    Heat the tip top of your angling rod with a lighter to loosen the adhesive. Set the rod horizontal and then you can easily reach the tip. Hold a lighter underneath the tip summit of the rod, which is the ringed piece at the cease of the rod, and heat it upward for iv-5 seconds at a fourth dimension. Once it's heated, try pulling information technology off with a pair of pliers or past hand. If it doesn't come up off hands, try heating it for another few seconds.[15]

    • Heating the tip top helps loosen the adhesive holding it in place so it's easier to remove.
    • If the tip snapped off of your rod, and then you can remove the old tip top from the broken slice or you tin skip this step.
  2. 2

    Smooth the tip of the rod with sandpaper to remove whatever shards. Rub the exposed tip of the rod with 120- or 220-grit sandpaper to smooth it out. Rotate the rod around the sandpaper until the tip is smooth and flush. It's okay if in that location are small abrasion marks on the rod tip since it volition have better adhesion to the new tip meridian.[16]

    Tip: If sandpaper isn't plenty to remove the shards on the end of your fishing rod, then carefully cut off the ends with a pair of scissors.

  3. 3

    Cutting pieces of rod cement into strips that fit within your new tip top. Rod cement is an adhesive that comes in a solid block and is used for fishing rods to concord guides and tips in identify. Use a razor or craft knife to cut out small strips of the rod cement so they fit within the hollow chamber on your rod tip height.[17]

    • Yous tin can purchase rod cement and new tip tops from your local sporting appurtenances store or online.
  4. 4

    Melt the rod cement inside the tip superlative with your lighter. Hold the new tip top with a pair of pliers and put the pieces of rod cement in the hollow tube at the end of it. Utilise your lighter to heat the rod cement for 4-five seconds and melt information technology so you tin attach information technology to your rod. Once the rod cement is melted, work apace and then it doesn't solidify once more.[18]

  5. five

    Slide the tip top onto your rod so information technology lines up with the guides and let information technology dry. While the cement is nevertheless hot, slide it onto the tip of your rod and rotate information technology so the ring is in line with the other guides. Wipe away any excess rod cement with a slice of paper towel and let it prepare for at to the lowest degree ane-ii hours. Once the cement is dry out, your rod is ready to utilize![19]

    • If you demand to adjust or reposition the tip top after the cement is dry out, so heat information technology once again for 3-4 seconds with your lighter.

    Advertizement

Add New Question

  • Question

    Where do I buy epoxy resin glue?

    Community Answer

    At any dwelling improvement or hardware store.

Inquire a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Advertisement

  • Accept your rod to a fishing supply store or a repair person if y'all have trouble fixing it on your ain.

  • If you need to prepare a snapped rod in an emergency, overlap the pieces by 6 inches (15 cm) and tape them together tightly.[20]

Thanks for submitting a tip for review!

Advertisement

  • Don't hold a flame against your rod longer than a few seconds or else you could permanently damage the rod.

  • Be careful while working with razor blades so you don't accidentally cutting yourself.

Advert

Things You lot'll Need

  • Scissors
  • Sandpaper
  • Tape measure
  • Fiberglass pole
  • Hacksaw
  • two-part epoxy
  • Bowl
  • Paintbrush
  • Electrical tape (optional)
  • Razor blade
  • Lighter
  • Sandpaper
  • Masking tape
  • Rod guides
  • Thread
  • 2-function epoxy
  • Dish
  • Paintbrush
  • Lighter
  • Pliers
  • Sandpaper
  • Rod cement
  • Craft knife
  • Rod tip top

Nearly This Commodity

Article Summary X

To fix a snapped angling rod, attempt using a fiberglass pole and some epoxy. Beginning, sand the snapped edges to make them flush. Polish edges are stronger and less likely to break. Cut a 12 inch long piece of fiberglass pole using a hacksaw. Slide ane end of the pole into your fishing rod until there are 6 inches sticking out. Once the fiberglass pole fits snugly into the rod, apply epoxy to the exposed end using a paintbrush. Connect the 2d half of the cleaved rod to the fiberglass pole and allow the epoxy set. To supplant the rod guide, starting time, remove whatsoever threading from around the guide using a arts and crafts knife. Align the new guide onto the rod and use tape to hold it in place. Wrap the new thread over the guide and then cover it in epoxy to prepare it. For more ideas on fixing a broken fishing rod, like how to change a rod tip, read on.

Did this summary assistance you?

Thanks to all authors for creating a page that has been read 210,453 times.

Did this article help you?

How To Repair A Loose Rod Tip,

Source: https://www.wikihow.com/Fix-a-Broken-Fishing-Rod

Posted by: kileswenoboy75.blogspot.com

0 Response to "How To Repair A Loose Rod Tip"

Post a Comment

Iklan Atas Artikel

Iklan Tengah Artikel 1

Iklan Tengah Artikel 2

Iklan Bawah Artikel